Im ProgrammGenerator können in den Pin-Makros auch logische Pin-Namen verwendet werden.
eine ProgGenerator Konfiguration funktioniert somit ohne Änderung für Arduino und ESP32.
| LED-Bus | Arduino-Pin LED-Nano | ESP32 |
|---|---|---|
| LED0 (Haupt-LED-Bus, der über den Wannenstecker unten rechts ausgegeben wird) | D6 | 27 |
| LED1 (PushButtons) | A4 | 32 |
| LED2 (Nur ESP32) | 16 | |
| LED3 (Nur ESP32) | 14 | |
| LED4 (Nur ESP32) | 18 | |
| LED5 (Nur ESP32) | 19 | |
| LED6 (Nur ESP32) | 23 | |
| LED7 (Nur ESP32 mit 38 Pins) | 0 | |
| LED8 DMX oder LED Kanal | 2 | 17 |
| Pin-Nummer Wannenstecker | Name | alternative Namen | Arduino-Pin LED-Nano | ESP32 GPIO |
|---|---|---|---|---|
| 1 | KEY80_P1 | D2 | 17 | |
| 2 | KEY80_P2 | D7 | 12 | |
| 3 | KEY80_P3 | D8 | 26 | |
| 4 | KEY80_P4 | D9 | 25 | |
| 5 | KEY80_P5 | D10 | 5 | |
| 6 | KEY80_P6 | D11 | 23 | |
| 7 | KEY80_P7 | D12 | 19 | |
| 8 | KEY80_P8 | A1 | 4 | |
| 9 | KEY80_P9 | KEY80_BUTTONS | A2 | 34 |
| 10 | KEY80_P10 | KEY80_RESET_K KEY80_RST | A3 | 33 |
| 11 | KEY80_P11 | KEY80_LEDS_K KEY80_SDA | A4 | 32 |
| 12 | KEY80_P12 | KEY80_SCL | A5 | 39 |
| 13 | - | 5V | ||
| 14 | - | GND | ||
—-
| Pin-Nummer Wannenstecker | Name | alternative Namen | Arduino-Pin LED-Nano | ESP32 GPIO |
|---|---|---|---|---|
| 1 | KEYBRD_P1 | KEYBRD_LEDS_K | A4 | 32 |
| 2 | A5 | 39 | ||
| 3 | 5V | |||
| 4 | GND | |||
| 5 | KEYBRD_P5 | KEYBRD_CLOCK_K KEYBRD_CLK | A0 | 15 |
| 6 | KEYBRD_P6 | KEYBRD_RESET_K KEYBRD_RST | A3 | 33 |
| 7 | KEYBRD_P7 | KEYBRD_BUTTONS | A2 | 34 |
| 8 | A7 (Jumper „KEY_A7“ schließen) Deaktiviert Tag/Nacht Schaltung | 35 | ||
| Pin-Nummer Wannenstecker | Name | alternative Namen | Arduino-Pin LED-Nano | ESP32 GPIO |
|---|---|---|---|---|
| 6 | KEYBRD1_P6 | KEYBRD1_RESET_K KEYBRD1_RST | A3 | 33 |
| 7 | KEYBRD1_P7 | KEYBRD1_BUTTONS | A2 | 34 |
| 8 | KEYBRD1_P8 | A6 (Jumper „SJ4“ schließen) | 36 |
| Pin-Nummer Wannenstecker | Name | alternative Namen | Arduino-Pin LED-Nano | ESP32 GPIO |
|---|---|---|---|---|
| 3 | CAN_P3 | CAN_CS | D10 | 5 |
| 4 | CAN_P4 | CAN_SO | D12 | 19 |
| 5 | CAN_P5 | CAN_SI | D11 | 23 |
| 6 | CAN_P6 | CAN_CLK CAN_SCK | D13 | 18 |
| Pin-Nummer Wannenstecker | Name | alternative Namen | Arduino-Pin LED-Nano |
|---|---|---|---|
| 1 | BOOT_P1 | BOOT_SO | D12 |
| 3 | BOOT_P3 | BOOT_SCK | D13 |
| 4 | BOOT_P4 | BOOT_SI | D11 |
| farbige Markierung am Bild | Name | alternative Namen | Arduino-Pin LED-Nano | ESP32 GPIO |
|---|---|---|---|---|
| rot | LDR | J1_P2 | A7 | 35 |
| grün | JP3_P2 | D13 | 18 | |
| orange | JP4_P3 | D10 | 5 | |
| rosa | SV1_P2 | D2 (Jumper „LED_BUS2B“ schließen) | 17 | |
| türkis | SV3_P2 | D6 über R1 | 27 |
| Pin-Nummer Wannenstecker | Name | alternative Namen | GPIO vom ESP32 30 Pin | GPIO vom ESP32 38 Pin |
|---|---|---|---|---|
| 1 | MLL_EXT_OUT_P1 | MLL_EXT_OUT_SCL | D22 | |
| 2 | MLL_EXT_OUT_P2 | MLL_EXT_OUT_SDA | D21 | |
| 5 | MLL_EXT_OUT_P5 | LED2 | D16 (RX2) | D16 |
| 6 | MLL_EXT_OUT_P6 | LED3 | D14 | |
| 7 | MLL_EXT_OUT_P7 | LED4 | D18 | |
| 8 | MLL_EXT_OUT_P8 | LED5 | D19 | |
| 9 | MLL_EXT_OUT_P9 | LED6 | D23 | |
| 10 | MLL_EXT_OUT_P10 | LED7 | — | D0 |
